Roland Fantom-Xa Manual do Utilizador Página 219
- Página / 264
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
219
Troubleshooting
If the Fantom-Xa does not function in the way you expect, first check
the following points. If this does not resolve the problem, consult
your dealer or a nearby Roland Service Station.
* If any sort of message is being displayed on the screen during an
operation, refer to
Error Messages
(p. 225).
The power does not turn on.
Make sure that the Fantom-Xa’s AC adaptor is connected
correctly to its power inlet and to the AC outlet (p. 15).
There is no sound.
Check the following points.
• Is the power for connected amps and speakers turned on? Is the
volume turned all the way down?
• Is the VOLUME knob turned all the way down?
• Have connections been made correctly?
• Can you hear sound through headphones?
If there is sound in the headphones, it is possible that the
connection cables are broken, or that your amp/mixer has
malfunctioned. Check your cables and amp/mixer system once
again.
• If you do not hear sound when you play the keyboard, check
whether the Local Switch is turned OFF.
Make sure that the Local Switch parameter is turned on (p. 197).
• Have all tones in the patch been turned off?
Turn on “Tone Switch.”
• The Part level settings may be too low.
Access the Level parameter, and check the level of each part (p.
73).
• Are the Effect settings correct?
Check the Effect settings ON or OFF, the Effect Balance or Level
(p. 157).
• Are the settings for the output destination correct?
Check the various output assign settings (p. 74).
• Is the Wave Expansion Board properly installed?
When selecting the settings that stipulate the use of EXP waves,
Patches, or Rhythm Sets, check that the Wave Expansion Board
is installed properly in the slot (p. 214).
• Has the volume been lowered by pedal operations or by MIDI
messages (volume messages or expression messages) received
from an external MIDI device?
• Have the samples been loaded correctly? (p. 153)
A specific Part does not sound.
Check the following points.
• Has the volume level of the part been lowered?
Adjust the Level parameter to raise the volume of the part that
is not heard (p. 73).
• Is the part being muted?
Set the Mute parameter to “OFF” (p. 73).
Specific pitch ranges do not sound.
Has a restricted range of notes been set?
If a specific range of notes does not sound, check the Key Range
settings for the Patch Tone, the Performance Part.
•
Tone Key Range
Key Range Lower/Key Range Upper parameter (p. 42)
•
Part Key Range
K.L/K.U parameter (p. 75)
The sound is distorted.
Check the following points.
• Is an effect which distorts the sound being applied?
If the sound for a specific patch or part is distorted, lower the
volume level on that part.
• If all sounds are distorted, use the VOLUME knob to lower the
volume level.
• Could the Output Gain be excessively high?
In “System,” check the “Sound” parameter.
Pitch is incorrect.
Check the following points.
• Is the tuning of the Fantom-Xa incorrect?
Check the Master Tune parameter setting (p. 194).
• Has the pitch been changed by pedal operations or by Pitch
Bend messages received from an external MIDI device?
• Have the Coarse Tune or Fine Tune parameters been set for
specific Parts?
Check the Coarse Tune parameter and Fine Tune parameter
settings (p. 74).
The sound is interrupted.
Sounds will be interrupted if more than 128 voices are used
simultaneously.
• Reduce the number of Tones that you are using.
• Increase the Voice Reserve setting for parts that must not drop
out (p. 75).
When I play the keyboard, notes do not stop.
Is the pedal polarity of the Hold Pedal reversed?
Check the Hold Pedal Polarity parameter setting (p. 195).
Problems Concerning the Entire
Fantom-Xa
Issues Related to Sound
Fantom-Xa_e.book 219 ページ ２００４年１０月２２日 金曜日 午後２時３分
- Owner’s Manual 1
- DECLARATION OF CONFORMITY 2
- IMPORTANT NOTES 4
- Using Memory Cards 5
- Contents 10
- Main Features 11
- Panel Descriptions 12
- Rear Panel 14
- Getting Ready 15
- Turning On/Off the Power 16
- Adjusting the Display 16
- Contrast (LCD Contrast) 16
- Listening to the Demo Songs 17
- Various Performance Features 18
- Overview of the Fantom-Xa 19
- About Memory 21
- About the Onboard Effects 22
- About the Sequencer 23
- About the Sampling Section 25
- Switching the Sound 26
- Generator Mode 26
- About the Function Buttons 26
- Moving the Cursor 27
- Changing a Value 27
- Assigning a Name 28
- Playing in Patch Mode 29
- Selecting a Patch 30
- Selecting Patches from the 30
- Selecting Favorite Patches/ 31
- Rhythm Sets (Favorite Patch) 31
- Selecting Patches by 32
- Category 32
- Affected by the Controller 34
- Creating a Patch 35
- Saving Patches You’ve 37
- Created (Write) 37
- Functions of Patch Parameters 38
- [F3 (PORTMNT)] 41
- [F1 (WG PRM)] 43
- Parameter Group [F2 (WG)] 43
- [F2 (PITCH)] 44
- [F3 (PCH ENV)] 44
- [F1 (TVF PRM)] 45
- Parameter Group [F3 (TVF)] 45
- [F2 (TVF ENV)] 46
- [F1 (TVA PRM)] 47
- Parameter Group [F4 (TVA)] 47
- [F2 (TVA ENV)] 48
- [F1 (CTRL1)]–[F4 (CTRL4)] 49
- Parameter Group [F5 (CTRL)] 49
- [F5 (MISC)] 51
- [F1 (LFO 1)], [F2 (LFO 2)] 52
- Modulating Sounds/Output 52
- How to Apply the LFO 53
- [F3 (STEP)] 54
- [F4 (OUTPUT)] 54
- Creating a Rhythm Set 55
- Copying Rhythm Tone Settings 56
- Saving Rhythm Sets You’ve 57
- Parameter Group [F4 (TVF)] 62
- Parameter Group [F5 (TVA)] 64
- Output Settings 65
- Playing in Performance Mode 66
- Selecting a Performance 67
- Using the LAYER Screen 68
- Part 1: Strings 69
- Part 1 + Part 2: 69
- (Strings + Piano) 69
- Part 2: Piano 69
- Using the MIXER Screen 70
- Silencing the Playback of a 71
- Specific Part (Mute) 71
- Creating a Performance 72
- Functions of Parameters of 73
- Each Part 73
- (Performance Parameters) 73
- [F3 (PITCH)] 74
- [F5 (FX SRC)] 74
- [F6 (OFFSET)] 74
- [PAGE] - [F1 (VIBRATO)] 75
- [PAGE] - [F2 (KEYBORD)] 75
- [PAGE] - [F3 (KEY MOD)] 76
- [PAGE] - [F6 (EXT)] 77
- Settings for the Realtime 78
- Controllers and D Beam 78
- Controller 78
- MIDI Settings 79
- D Beam Controller 80
- Solo Synth 81
- Pad Trigger 82
- Assignable 82
- Realtime Controller 83
- ASSIGNABLE Switch Settings 84
- Control Pedal 85
- Playing Arpeggios 86
- Arpeggio Settings 87
- Variations (Arp Motif) 89
- Creating an Arpeggio Style 90
- (Arpeggio Style Edit) 90
- Saving the Styles You Have 91
- About the Chord Memory 92
- Performing with the Chord 92
- Memory Function 92
- Playing Rhythms 94
- Pattern Performances 95
- Select the Rhythm Group 95
- Rhythm Pattern Settings 96
- Creating a Rhythm Pattern 97
- (Rhythm Pattern Edit) 97
- Saving the Rhythm Pattern 98
- You Have Created (Write) 98
- Sampling 100
- External Input Settings 101
- Input Effect Setup Settings 102
- Skip Back Sampling 103
- Editing a Sample 104
- Sample Edit 106
- Sample (NORMALIZE) 109
- Maximizing the Volume of a 109
- Assigning Samples to a Pad 112
- (Assign to Pad) 112
- Assigning a Sample as a 113
- Patch to a Part (Assign to 113
- Keyboard) 113
- Saving a Sample (Write) 116
- Using the Pads 117
- Assigning a Pattern to a 118
- Pad (RPS Function) 118
- Using the Pads to Play 118
- Playing Back a Song 119
- Various Playback Methods 120
- Recording Songs 122
- Recording Your 124
- Performance as You Play It 124
- (Realtime Recording) 124
- Quantize) 126
- Inputting Data One Step at 128
- Editing Songs 131
- Editing Sequencer Data 133
- Over the Specified Range 133
- (Track Edit) 133
- Aligning a Song’s Timing 134
- (Quantize) 134
- Copying Phrases (Copy) 137
- Transpose the Key (Transpose) 138
- Sequencer Data (Extract) 141
- Shifting Performance Data 142
- Editing Individual Items of 144
- Sequencer Data (Micro Edit) 144
- Sequencer Data Handled by a 145
- Phrase Track/Pattern 145
- Viewing Sequencer Data (View) 146
- Moving Sequencer Data (Move) 147
- Copying Sequencer Data (Copy) 148
- Changing the Tempo Midway 148
- Through the Song 148
- Assigning a Name to a 149
- Song (Song Name) 149
- Saving a Song (Save) 150
- Saving a Song (Save Song) 151
- Saving a Song as an SMF 152
- File (Save as SMF) 152
- Loading a Song (Load) 153
- Before You Use the RPS 154
- Function 154
- Using the RPS Function 156
- While You Perform 156
- Adding Effects 157
- Multi-Effects Parameters 164
- 12: STEP PHASER 168
- 13: MULTI STAGE PHASER 168
- SAW1 SAW2 169
- 20: SLICER 170
- 21: ROTARY 170
- 23: CHORUS 171
- 24: FLANGER 171
- 26: HEXA-CHORUS 172
- 28: SPACE-D 172
- 31: 3D STEP FLANGER 173
- 35: OVERDRIVE 175
- 38: VS DISTORTION 175
- 42: GATE 177
- 44: LONG DELAY 177
- 47: 3TAP PAN DELAY 178
- 50: REVERSE DELAY 179
- Feedback 180
- 56: LOFI NOISE 181
- 57: LOFI COMPRESS 182
- 60: PHONOGRAPH 182
- 61: PITCH SHIFTER 183
- (Feedback Pitch Shifter) 183
- 63: STEP PITCH SHIFTER 183
- Balance W 184
- Balance D 184
- Making Chorus Settings 189
- Making Reverb Settings 190
- Mastering Effect 191
- [F2 (AUTO LD)] 193
- System Menu [F1 (GENERAL)] 193
- [F1 (COMMON)] 193
- [F3 (SOUND)] 194
- [F4 (USB)] 194
- [F1 (KBD)] 195
- [F2 (PDL BND)] 195
- System Menu [F2 (KBD/CTRL)] 195
- [F3 (KNOB SW)] 196
- [F4 (CTRL)] 196
- [F1 (GENERL)] 197
- System Menu [F3 (MIDI)] 197
- Using the Local Switch 197
- [F2 (TX)] 198
- [F3 (RX)] 198
- [F4 (MMC MTC)] 198
- MIDI Clock and MTC 199
- Types of MTC 199
- [F1 (METRO)] 200
- [F2 (REC TRK)] 200
- [F3 (SYNC)] 200
- System Menu [F4 (SEQ/TEMPO)] 200
- [F2 (TRIGGER)] 201
- [F3 (ASSIGN)] 201
- System Menu [F5 (D BEAM)] 201
- [F4 (DB SYN)] 202
- Data Management Functions/ 203
- Basic Procedure 204
- About USB Functions 206
- Switching the USB Storage 206
- Mode and the MIDI Mode 206
- Your Computer 207
- (Storage Mode) 207
- Exiting Storage Mode 208
- Canceling USB Communication 208
- Importing an Audio File 208
- (Import Audio) 208
- Exchanging MIDI Messages 209
- (MIDI Mode) 209
- Using Fantom-X Editor 210
- Fantom-X Editor System 211
- Requirements 211
- About V-LINK 212
- V-LINK Parameters 213
- Resetting the Image 213
- Checking the Installed Wave 215
- Expansion Board 215
- Expanding the Memory 216
- Checking that memory is 217
- Using a Memory Card 218
- Troubleshooting 219
- Issues Related to Effects 221
- Issues Related to Saving Data 221
- Issues Related to Sequencer 222
- Issues Related to MIDI and 223
- External Devices 223
- Issues Related to Sampling 224
- Error Messages 225
- Performance List 226
- Patch List 227
- GM (GM2 Group) 231
- Rhythm Set List 232
- Waveform List 241
- Arpeggio Style List 244
- Chord Form List 244
- Rhythm Group List 245
- Rhythm Pattern List 246
- USER (User Group) 247
- PRST (Preset Group) 247
- About MIDI 248
- MIDI Implementation Chart 249
- Specifications 251
Manuais e produtos relacionados com Instrumentos Musicais Roland Fantom-Xa
Instrumentos Musicais Roland PCR-80 Manual do Utilizador
(184 páginas)
(184 páginas)
Instrumentos Musicais Roland FR-1 Manual do Utilizador
(100 páginas)
(100 páginas)
Instrumentos Musicais Roland RS-70 Manual do Utilizador
(181 páginas)
(181 páginas)
Instrumentos Musicais Roland VG-99 Manual do Utilizador
(191 páginas)
(191 páginas)
Philips AJ3500 manuály
Uživatelské manuály a uživatelské příručky pro Budíky Philips AJ3500.
Poskytujeme 1 manuály pdf Philips AJ3500 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais