Roland VersaCamm SP-540V Manual do Utilizador

SA International Contour Cutting Guide SA International 2 International Plaza, Suite 625 Philadelphia, PA 19113-1518 USA 610-521-6300 www.scanvecam

© 2006 Scanvec Amiable, Inc. 8 4. Check the Send cut job box and select the cutter you want to use as the second half of your virtual hybrid.  Whe

© 2006 Scanvec Amiable, Inc. 9 Appendix A: Notes on Specific Output Devices GCC SignPal Jaguar III Cutting Contours Using the GCC Accu-Aligning Syst

© 2006 Scanvec Amiable, Inc. 10  Positive X values will cause the contour to shift down from its current position. Positive Y values will cause th

© 2006 Scanvec Amiable, Inc. 11 Gerber GS15, HS-15, HS-15 Plus, HS-750, HS-750 Plus To cut a contour using a Gerber cutter: 1. Add a setup for the

© 2006 Scanvec Amiable, Inc. 12 Graphtec 5100/5100A The 5100 series cutters are able to automatically align themselves using registration marks. Two

© 2006 Scanvec Amiable, Inc. 13 21. Place the knife within the lower-right mark and press the Origin button on the cutter. 22. Click OK in the

© 2006 Scanvec Amiable, Inc. 14 Graphtec FC7000 The 7000 series cutters are able to automatically align themselves using registration marks. Two dif

© 2006 Scanvec Amiable, Inc. 15 6. Click OK in the software. The cutter will automatically detect all of the remaining marks and cut them indi

© 2006 Scanvec Amiable, Inc. 16 Ioline SmarTrac Contour Cutters To cut a contour using Ioline registration marks: 1. Print the job and load the pri

© 2006 Scanvec Amiable, Inc. 17 Mimaki CG-60 EX, CG-100 EX, CG-130 EX Cutters To cut a contour using the Mimaki CG-60 EX, CG-100 EX, or CG-130 EX cu

© 2006 Scanvec Amiable, Inc. ii Contents Introduction...1 Hybr

© 2006 Scanvec Amiable, Inc. 18 Mimaki CG-75 FX, CG-130 FX, CG-160 FX Cutters To cut a contour using the Mimaki CG-75 FX, CG-130 FX, or CG-160 FX cu

© 2006 Scanvec Amiable, Inc. 19 Using One Set of Registration Marks for Multiple Copies of a Job When printing multiple copies of a job, the default

© 2006 Scanvec Amiable, Inc. 20 Mutoh SC-850D/1400D Cutting Jobs Using Automatic Mark Detection To cut a contour using the Mutoh SC-850D or 1400D cu

© 2006 Scanvec Amiable, Inc. 21 16. Select the .plt job file and click Send. Mark detection takes about 30 seconds before cutting. Printing Multip

© 2006 Scanvec Amiable, Inc. 22 Roland CAMMJET and SOLJET Devices  Applies to: Roland CAMMJET CJ-400/500, CAMMJET PRO II 540, SOLJET SC-500, SOLJE

© 2006 Scanvec Amiable, Inc. 23 Roland CAMMJET PRO 1 GX 24, GX 300, GX 400, GX 500 Cutting a Laminated Job The CAMMJET GX series cutters default to

© 2006 Scanvec Amiable, Inc. 24 7. Send your print job. a. After the printing, be sure to advance AT LEAST 6” before cutting the sheet. b. Allow

© 2006 Scanvec Amiable, Inc. 25 Summa OPOS Automatic Positioning Using OPOS Marks To cut a contour using the Summa cutters: 1. If you will be runni

© 2006 Scanvec Amiable, Inc. 1 Introduction This guide is intended to help Scanvec Amiable users to output accurate and high-quality contour cut job

© 2006 Scanvec Amiable, Inc. 2 Creating Output Device Setups Setups provide the link between the software and your output devices. Each setup contai

© 2006 Scanvec Amiable, Inc. 3 Designing Contour Cut Jobs in Flexi Contour cut jobs contain both a printed element, and one or more contour cuts. Co

© 2006 Scanvec Amiable, Inc. 4 Height of the contour shape (Ellipse or Rectangle). Proportional Check this value to assure that the cutting line wi

© 2006 Scanvec Amiable, Inc. 5 Outputting Contour Cut Jobs in Flexi There are two stages to outputting jobs in Flexi. First, the job is sent to Pro

© 2006 Scanvec Amiable, Inc. 6 Outputting Contour Cut Jobs from Production Manager There are slightly different procedures to follow when outputting

© 2006 Scanvec Amiable, Inc. 7 Outputting Contour Cut Jobs in PhotoPRINT Setting Up a Job for Contour Cutting In order for a contour to be cut when