Roland CX-400 Especificações Página 28
- Página / 64
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
28
CX-500
CX-400
CX-300
1195 mm (47 in.)
1000 mm (39 in.)
737 mm (29 in.)
24998 mm
(984-1/8 in.)
10 mm
30 mm
(1-3/16 in.)
25 mm (*)
(1 in.)
Initial cutting coordinate
origin point (0,0)
Movable Pinch
Roller (Left)
Pinch roller (right)
1 mm
15 mm
Material
Cutting area
The pairs of allows
indicate the positive
direction along the X
and Y axis.
Brake
About the Cutting Area
The cutting area along the horizontal plane (the direction in which the tool carriage moves) is determined by the position of the pinch
rollers. The workable area spans the length between the two rollers, minus a margin of about 1 mm (about 0.04 in.) on both sides.
If the material length is greater than 1,600 mm (63 in.) when a flat material has been loaded, the CX-500/400/300 determines it to be
a rolled material and sets the material length to 24,998 mm (984-1/8 in.). Also, when loading flat material (that is, when [PIECE] has
been selected), a piece of material that is about 100 mm (3-15/16 in.) longer than the vertical size of the cutting data is required.
* When you select [F-EDGE] or [PIECE],
this is 25 mm. When you select [ROLL],
everything toward the front from the
origin point is the margin. (See “The
Location of the Origin Point Immediately
After Loading Material” elsewhere in this
section.) When you have separated the
material using the [SHEET CUT] key,
this is the value set for [MARGIN] at the
[AUTOCUT MENU]. Refer to “7-3 List of
Functions.”
When performing material feed or cutting, be sure to release the brake.
Attempting to perform material feed or cutting with the brake engaged may make normal feed impossible and
cause the material to slip and cause a motor error.
NOTICE
The longer is the cut material, the greater are the chances that the material will become crooked or come loose. This means that it is
important to load the material straight, make sure the margins are wide enough, and perform test feed to check the material feed.
The high-accuracy sheet hanger and brake on this machine can minimize crookedness of material.
Have on hand a piece of material that's at least 50 mm (2 in.) wider than the cutting width.
The chance of the material slipping loose from the pinch rollers can be reduced by braking the shaft and loading the pulled-out
material while it's in a tensioned state, which lets you load the material straight. Follow the steps below to load the material.
5-3 To Perform Lengthy Cutting
1
Place the rolled material on the shaft and engage the
brake for the shaft.
- Table of Contents 2
- 2 Part Names and Functions 3
- 1 Checking Supplied Items 3
- 2-2 Rear View 4
- 2-3 Operation Panel 4
- 3 Setup 5
- 3-2 Connection 6
- 3-3 Turning on the Power 7
- 4 Basic Operation 8
- Loading Roll Material 9
- Material Loading Position 10
- Rear View 13
- 4-2 Installing a Blade 14
- Cutting Test 15
- Adjusting the Blade Force 16
- 4-4 Setting the Origin Point 17
- 4-5 Starting Cutting 18
- To Sever the Material 19
- Pausing Cutting Operations 19
- Tool carriage 20
- Tool securing screw 20
- Turn off the power 21
- 5 Advanced Operation 22
- Settings for Cutting Quality 24
- (1-3/16 in.) 26
- Pinch Roller 26
- Material 26
- Coordinate Rotation Settings 27
- About the Cutting Area 28
- Roll material 29
- Material, Etc.) 30
- 5-6 Front Loading 32
- Setting the Origin Point 33
- * Windows 95/98/Me only 34
- 5-7 The Overcut Feature 35
- 5-8 The Preset Feature 36
- Calling Up 37
- Deleting Settings 37
- 0.25 mm (0.01 in.) 40
- 6-2 About Special Materials 41
- 7 Descriptions of Features 42
- Power on 43
- TOP MENU 43
- [MENU] + Power on 43
- MENU MODE 44
- 7-3 List of Functions 46
- Description of Menu Items 47
- TYPE 1 TYPE 2 48
- 8 Maintenance 50
- 8-2 Consumable Items 51
- Worn areaNew part 51
- Positioning groove 52
- 9 If There Is a Problem 53
- 9-2 What to do if 54
- The carrier paper is cut 56
- 9-3 Error Messages 58
- 10 Specifications 59
- [Parallel] 61
- [USB connector] 61
- : Compatible 62
- : Incompatible 62
- : Ignored 62
- - MEMO 63
- R5-020403 64
Manuais e produtos relacionados com Digitalizar e Imprimir Roland CX-400
(5 páginas)
(68 páginas)
(183 páginas)Faber Fans user manuals
The list of Faber Fans products contains 53 user manuals for 53 models. All pdf user’s guides are available for download or viewing online.
Comentários a estes Manuais