Roland PNC-950 Manual do Utilizador

ROLAND DG CORPOR ATIONPNC-950PNC-950PNC-950PNC-950PNC-950USER'S MANUAL

4• Operation Panel* The TEST key and the cursor keys functiononly when the SETUP LED is lighted, andthe ROTATE key functions only when theSETUP LED is

54 BASIC OPERATION4-1 Setting Up and Connection• Setting UpWhen arranging setup space for the PNC-950, make sure you have a space that is at least 905

64-2 DIP Switch SettingsDIP switches settings must be made only when the power is turned off.The DIP switches are located on the right-hand side of th

72) Press the push-pin andremove the blade fromthe blade holder.Blade holderPush-pinBlade• Blade adjustment may be necessary in the following cases:-

84-4 Loading the Sheet — SETUP Key• Turning on the PowerSwitch on the power switch on the left side of the PNC-950.When the power switch is pressed to

9(1) Lower the sheet loading levers to raise the movable pinch rollers on the left and right, and move each of the pinch rollers all the wayto its res

10If You Are Using a Flat Sheet- Ideally, the PNC-950 should be set up as shown in figure A or B below. If you are using a different setup configurat

11Movable pinch roller (left)SheetGuide lineSheetSheet loading leverPinch roll frameBack of thePNC-950Front of thePNC-950(5) After positioning the pin

12• About the Cutting AreaAbout 1 mm (about 0.04")24,998 mm(984-1/8")Cutting coordinateorigin (0,0)About 15 mm (about 9/16")Movable Pin

134-6 Cutting Test to Check Blade Force — , , , , and TEST KeysBefore carrying out actual cutting, you may wish to perform a "cutting test&qu

CAUTION1) Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.2) The contents of this operation manual and the spec

144-7 Downloading Cutting DataThe unit will begin cutting when it receives cutting data sent from the computer.• Software SettingsWhen cutting with co

15• Continuing CuttingCutting After Changing the SheetFollow the procedure described from "Loading the Sheet" on page 8 to "4-7 Downloa

164-9 When Cutting Is Completed(1) When cutting is finished, press down the sheet loading levers and remove the sheet. (See "Removing the Sheet&

175 SETTINGS FOR EACH FUNCTION• Using a sheet effectively and cutting along the vertical dimension(Rotate function) -- ROTATE Key and ROTATE LEDThis f

18• Plotting on Paper Media — PEN MODE Key and PEN MODE LEDThe PNC-950 is also capable of plotting on paper media using plotter pens made by this comp

196 ABOUT THE BLADEIf the blade becomes dullWhen the blade starts to lose its sharpness, try gradually increasing the blade force (refer to page 13, &

207 WHAT TO DO IF...If the PNC-950 doesn't run...PNC-950• Is the PNC-950 power on?Turn on the power.• Is the unit in SETUP status (the SETUP LED

21The POWER/ERROR LED is blinkingIf there is an error in the data downloaded to the PNC-950 from the computer, the PNC-950 generates an error (the POW

228 LIST OF CAMM-GL III INSTRUCTIONS*1: -(226-1) — +(226-1) *2: 0 — +(226-1) *3: -(226-1)° — +(226-1)° *4: 21(16) — 3A(16), 3C(16) — 7E(16)• mode1• m

23• Instructions in mode1 and mode2Instruction Format Meaning of Parameter [Parameter Range (Default)] ExplanationIW IW LLx, LLy, URx, URy; LLx, LLy

iTypographic ConventionsThis manual uses certain typographic symbols, outlined below.This indicates a point requiring particular care to ensure safe u

249 LIST OF DEVICE CONTROL INSTRUCTIONSDevice control instructions are used to determine the communication sequence between the PNC-950 and computerth

25Instruction Format Parameter Range ([ ] is default) Explanation ESC .E [ESC].E None Outputs an error code related to RS-232C interface Output R

26Automatic backspace10 CHARACTER SETS

2711 LIST OF OPTIONSOption name Product number DescriptionSpare blade (for ZEC-U1005 Cemented carbide blade (5 pcs/set)standard vinyl sheet)Spare bl

2812 SPECIFICATIONS OF PNC-950, , , PNC-950Mechanism Media-movement methodMaximum cutting area Width: 584 mm (22-15/16")Length: 24,998 mm (984-

29• Interface SpecificationsParallel Connector (in compliance withspecifications of Centronics) Serial Connector (RS-232C)1191836SignalnumberTerminaln

C3070395BE V5-1

ii To Ensure Safe UseIf you find some abnormality, immediately turn off the power switch and check the user's manual to find out what iswrong. WA

iiiThese labels are affixed to the body of this product. The following figure describes the location and content of thesemessages. About the Labels A

ivTo Ensure Correct UseThis product is a precision instru-ment and must be handled with care.When the unit is not in use for anextended period, detach

1Thanks and Best WishesThank you very much for purchasing the CAMM-1 PNC-950.Since we wish you many years of productive use of your PNC-950, we ask yo

21 PRECAUTIONS IN USE• Ensure that the power supply voltage in within +/-10% of the machine's rated voltage.• Always be careful whenever the unit

33 PART NAMES AND FUNCTIONSDIP SwitchesUsed to make various settings.Pen Force Control SliderSets the blade force to be used with the tool.Parallel (C