Roland Metaza MPX-80 Manual do Utilizador descarregar pdf (Página 84)

Chapter 6 Appendix

6-1 What to Do If

The machine doesn't run even when printing data is sent.

Is the power switched on?

Make sure the Power/Movement button light is on. If it is

dark, press the Power/Movement button to switch on the

power.

Is the power cord connected correctly?

If it is not connected correctly, refer to the page indicated

below and connect it properly.

☞ P. 20, "Connecting the Cables"

Is the cable used for the connection to the computer

connected correctly?

If it is not connected correctly, refer to the page indicated

below and connect it properly.

☞ P. 20, "Connecting the Cables"

Striking is performed, but nothing is printed.

Is the material loaded at the correct location?

If striking is being performed at a location other than where

the material is loaded, then reload the material.

☞ P. 31, "Loading Material Using the Adhesive Sheet," p.34, "Loading Material

Using the Center Vise"

Is the material to be printed in line with the param-

eters for printable material?

Prepare and use printable material.

☞ P. 28, "Preparing Material to Print"

If you’re not using a head cap, has the height of the

head unit been adjusted to match the thickness of

the material?

When you’re not using a head cap, make sure the head unit

has been secured in place at an appropriate height for the

thickness of the material. Printing cannot be performed

unless the head unit is at the appropriate height. Adjust the

height of the head unit, then fasten it in place securely us-

ing the knob.

☞ P. 31, "Loading Material Using the Adhesive Sheet," p.34, "Loading Material

Using the Center Vise"

Is the marking pin bent or broken?

When nothing is printed, and changing the location where

the material is loaded, the parameters for the material, or

the height of the head unit does not correct the problem,

then the marking pin may be bent or broken. Try changing

to an unused marking pin and carry out test printing. If you

can print with the new marking pin, it means the marking

pin you had been using is bent or broken. Continue using

the new marking pin.

☞ P. 73, "Changing the Pin Used for Marking"

The image is unattractive.

Are the settings for the material in the driver's set-

ting window correct?

Choose the composition of the loaded material.

Even if the composition of the material is the same, the

hardness of the printed surface may vary greatly depending

on the casting method, the composition of impurities, the

presence of plating, and so on. In such cases, perform fine

adjustment of the striking force to match the material.

☞ P. 78, "Adjusting the Striking Force to Match the Material"

Is the image printed clearly?

If the image is not printed clearly, adjust the brightness of

the image. Perform printing while increasing the brightness

of [Gamma] or [Brightness] in the driver's setting window a

little at a time.

At this time, leave the material loaded and perform

overstriking at the same location. Continue changing set-

tings and performing printing until you obtain the darkness

you want.

☞ P. 64 "Driver Settings", driver Online Help "[Correction] tab"

Are grayscale tones printed clearly?

When grayscale tones are indistinct, go to the setting win-

dow for the driver (“Advanced” at the [Image Correction]

tab) and adjust the force of striking. Perform printing while

leaving the value for [Impact--MAX] unchanged and increas-

ing the value for [Impact--MIN] a little at a time.

At this time, leave the material loaded and perform

overstriking at the same location. Continue changing the

settings in the driver's setting window and performing print-

ing until you obtain the darkness you want.

☞ P. 78 "Registering a Composition and Adjusting the Striking Force"

More Information about Overstriking

The various setting values determined with overstriking are

effective only when performing overstriking under identi-

cal conditions. The same results are not necessarily obtained

when printing is performed with a new piece of material

with only the conditions made the same, without perform-

ing overstriking.

Is the marking pin worn?

Attractive printing may be impossible if the marking pin

becomes worn.

Adjust the pin or change it to a new one.

☞ P. 70, "Maintenance of the Head and the Marking Pins"

1 2 ... 79 80 81 82 83 84 85 86 87 88 89 ... 95 96

Comentários a estes Manuais

Sem comentários

Roland Metaza MPX-80 Manual do Utilizador Página 84

Comentários a estes Manuais

Manuais e produtos relacionados com Digitalizar e Imprimir Roland Metaza MPX-80